NanoVNA-F_V2 3G Mini Vector Network Analyser

NanoVNA-F_V2 is a new generation of portable, stand-alone vector network analyser with 4.3″ IPS LCD screen, metal enclosure, 5000mAh rechargeable battery (continuous operation for 7 hours low-power design) Based on edy555’s NanoVNA and OwOComm’s S-A-A-V2 you can expect superb performance from a small, incredibly affordable instrument that will cover 50Khz to 3GHz.

NanoVNA-F_V2 is a new generation of portable, stand-alone vector network analyser with 4.3″ IPS LCD screen, metal enclosure, 5000mAh rechargeable battery (continuous operation for 7 hours low-power design) Based on edy555’s NanoVNA and OwOComm’s S-A-A-V2 you can expect superb performance from a small, incredibly affordable instrument that will cover 50Khz to 3GHz.

The VNA is fitted with SMA connectors for easy adaption to the connector of your choice, please see accessories for our range of adapters.

The NanoVNA-F V2 comes in a suburb looking display, storage box that has a foam inlay to keep this lovely device out of harms way when not in use.

All in all this is a great value product punching way above its weight, grab one while you can these will go fast!

Specification

  •          Frequency range: 50kHz ~ 3GHz
  •          S11 dynamic range: 50dB(50kHz ~ 1.5GHz), 40dB(1.5GHz ~ 3GHz)
  •          S21 dynamic range: 70dB(50kHz ~ 1.5GHz), 60dB(1.5GHz ~ 3GHz)
  •          RF output power: -9dBm
  •          Frequency tolerance: 0.5ppm
  •          Screen: 4.3″ IPS LCD, 800*480, RTP touchpad
  •          Operation via touch screen or 3 side buttons
  •          Battery: 3.7V Li-Po, 5000mAh
  •          Aluminium enclosure: 125mm x 75mm x 20mm
  •          SMA female RF port
  •          Sweep points: 101
  •          Calibration result storage: 5
  •          Calibration result interpolating supported
  •          Traces: 4
  •          Markers: 4
  •          Measures: S-parameter, VSWR, smith chart, phase, polar, etc.
  •          Mark table can be moved up and down
  •          Firmware upgrade via U-disk with type-c cable
  •          USB power output: 5V/1A
  •          Compatible with NanoVNA-saver, support screenshot

PartList

  •          NanoVNA-F V2 x1
  •          20cm SMA-JJ RG405 cable  x2
  •          Calibration kit: SMA OPEN/SHORT/50ohm LOAD
  •          SMA-KK adapter x1
  •          SMA-JJ adapter x1
  •          SMA-JKW adapter x1
  •          USB Type-C cable x1
  •          Stylus x1

Resources

Review


Equipment

YAESU – FT-857D

YAESU – FT-857D

    YAESU – FT-857D The FT-857D, the world’s smallest HF/VHF/UHF mobile transceiver, provides base station-type performance from… Read more

Radio Shield RS-UV3

Radio Shield RS-UV3

The HobbyPCB RS-UV3 radio module is a 144/220/450 MHz FM transceiver board. The RS-UV3 is a low cost transceiver solution for Packet Radio, repeaters,… Read more


Antenna


App – Mobile

The post NanoVNA-F_V2 3G Mini Vector Network Analyser appeared first on QRZ NOW – Ham Radio News.

Leave a Reply