Nerfd.net – RF News & Info

ICOM IC705 firmware 1.27 has just been released

nerfd
Download Type Firmware
Model name IC-705
Version Version 1.27
Update 2022/05/20
Major changes Changes from Version 1.26Improved to enable forcing an All Reset by connecting an external power source (*) while holding down [RIT/ΔTX] and [XFC], even if you cannot turn ON/OFF the transceiver by using the [POWER] key.
* First, disconnect any external power supply, battery pack, and USB cable, and then reconnect any one of them.
Note You cannot revert to firmware version 1.24 or earlier on the serial numbers listed below, which have firmware version 1.26 or later installed.IC-705    #32: Serial number 32001001 or later
IC-705    #33: Serial number 33001001 or later
IC-705-T  #36: Serial number 36001001 or later
IC-705    #37: Serial number 37001001 or laterPlease note on the models listed above, if you revert to firmware version 1.24 or earlier, the audio will not be correctly output.
The CS-705 programming software used with this firmware can be downloaded here.To update the firmware1. Download and unzip the firmware data (for example, 705E127.dat) and copy it into the “IC-705” folder that is on your microSD card.2. Insert the microSD card with the firmware data into the transceiver. 3. Update the firmware.3-1. Display the SD CARD screen in the Menu. 3-2. Touch “Firmware Update” on the SD CARD screen to open the FIRMWARE UPDATE screen.3-3. Touch [▼] to scroll to the end of the screen to read all the precautions, after you read and agree with all the precautions, touch [YES]. 3-4. The confirmation dialog recommends making a backup of the settings and memories, touch [YES]. We recommend that you make a backup of them in this step, because all the settings and memories may be reset after updating the firmware.3-5. After the backup file is made, and the firmware selection screen is displayed, touch the firmware update data (for example, 705E127). 3-6. Please carefully read all the precautions, and when you want to execute it, touch [Yes] for 1 second to start the firmware update.3-7. When the update is completed, “Firmware updating has completed.” is displayed, and the transceiver will automatically restart.If the setting data needs to be converted, it may take some time to restart. 4. If the settings and memories have been reset, load the settings and memories that have been backed up onto the microSD card.4-1. Display the SD CARD screen in the Menu.4-2. Touch “Load Setting” on the SD CARD screen to open the LOAD SETTING screen. 4-3. Touch the file name of the saved file. 4-4. Touch “ALL,” and then the dialog “Keep ‘SKIP’ settings in the Repeater List?” is displayed, touch [YES].4-5. The dialog “Load file? The new “REF Adjust” setting will be saved.” is displayed, touch [Yes].4-6. After the loading ends, “COMPLETED! Restart the IC-705.” is displayed, restart the transceiver. After updating the firmware, the Version Information in the OTHERS Set will be as follows.Main CPU: 1.27Sub CPU: 1.01DSP Program: 1.11DSP Data: 1.00FPGA: 1.01DV DSP: 1.02GPS: 13196Bluetooth: 1.12WLAN: 2.0.0.0_2.2.0.7_3.17.0.4
File Size 8.17MB
File Type zip
Manual manual download page

DOWNLOAD IC-705 firmware 1.27

Antenna


Review

December 24, 2016
No comments

“This week I’m reviewing the Openspot by Shark RF. No images to hunt down, It runs D-Star, DMR & Fusion all in one box. Don’t fo… Read more


Equipment

Elecraft KX3 GoBox

September 24, 2015
No comments

As I was contacted by a few HAMs where to get “my” box I would like to give you a little parts-overview. Unfortunately I`m not able to manufacture thi… Read more

The post ICOM IC705 firmware 1.27 has just been released appeared first on QRZ NOW – Ham Radio News.

Exit mobile version